Router(config)#interface fastethernet 0/0: Enter into the FastEthernet 0/0 interface. Router(config-if)#description Development department: This command is optional. It will set description on interface. Router(config-if)#ip address 192.168.0.1 255.255.255.0: Assigns address and subnet mask to interface: Router(config-if)#no shutdown: Turns. Sep 26, 2012 It's fastethernet 0/0-12 (or 24 or 48). Commented: 2012-09-23. Ok - what is this then -copied and pasted here from my 2960 interface FastEthernet0 no. In Internet Explorer, click Tools, and then click Internet Options. On the Security tab, click the Trusted Sites icon. Click Sites and then add these website addresses one at a time to the list: You can only add one address at a time and you must click Add after each one.
Table of contents- 1.Preparation
- 2.Cisco Router's Configuration Sample #1 (Having a Fixed Physical IP Address)
- 2.1.Example Environment
- 2.2.Cisco Configuration Sample
- 3.Cisco Router's Configuration Sample #2 (Having a DHCP-Assigned Physical IP Address)
- 3.1.Example Environment
- 3.2.Cisco Configuration Sample
- 4.Cisco Router's Configuration Sample #3 (PPPoE WAN Connection)
- 4.1.Example Environment
- 4.2.Cisco Configuration Sample
Most of Cisco's routers which are released on or after 2005 has L2TPv3 over IPsec protocol function. (If not, you might be able to upgrade the IOS version to support it.)
- Why Cisco Routers with SoftEther VPN Server is the Best?
The above link shows the advantage of SoftEther VPN Server with the combination with Cisco Routers.
Preparation
Before setup Cisco router you have to setup the SoftEther VPN Server settings.
Understand 4 0 925 download free. On the above screen, check the 'Enable EtherIP / L2TPv3 over IPsec Server Function' and click the 'Detail Settings' button. The following screen will appear.
In this screen you have to define a mapping-table between L2TPv3 client (router)'s ISAKMP (IKE) Phase 1 ID, and the destination Virtual Hub's name, username and password.
On the above example, VPN connection attempts from any L2TPv3 routers will be regarded to use the 'l2tpv3' username to connect the 'DEFAULT' Virtual Hub. (The 'l2tpv3' user must be registered on the Virtual Hub.)
Essentially you should specify the Cisco's router's ISAKMP (IKE) Phase 1 ID on the ID field. However, you can specify '*' (wildcard) to match for any IDs. This is lack of security but this time is just a tutorial. So a wildcard is used. In the long-term running system you have to specify the Phase 1 ID exactly instead of a wildcard.
Cisco Router's Configuration Sample #1 (Having a Fixed Physical IP Address)
Example Environment
- Ethernet Ports
FastEthernet 0: WAN Port (IP Address: 2.3.4.5 / Subnet Mask: 255.255.255.0 / DefGW: 2.3.4.254)
FastEthernet 1: Bridge Port - Destination SoftEther VPN Server IP Address
1.2.3.4 - ISAKMP SA Encryption Settings
AES-256 / SHA / DH Group 2 (1024 bit) - IPsec SA Encryption Settings
AES-256 / SHA - IPsec Pre-Shard Key
vpn
Cisco Router's Configuration Sample #2 (Having a DHCP-Assigned Physical IP Address)
Example Environment
- Ethernet Ports
FastEthernet 0: WAN Port (Automatic Lease IP Address from DHCP Server)
FastEthernet 1: Bridge Port - Destination SoftEther VPN Server IP Address
1.2.3.4 - ISAKMP SA Encryption Settings
AES-256 / SHA / DH Group 2 (1024 bit) - IPsec SA Encryption Settings
AES-256 / SHA - IPsec Pre-Shard Key
vpn
Cisco Router's Configuration Sample #3 (PPPoE WAN Connection)
Interface Fastethernet 0/0
Example Environment
Interface Fastethernet 0/0
- Ethernet Ports
FastEthernet 0: WAN Port (Automatic Obtain IP Address via PPPoE)
FastEthernet 1: Bridge Port - Destination SoftEther VPN Server IP Address
1.2.3.4 - ISAKMP SA Encryption Settings
AES-256 / SHA / DH Group 2 (1024 bit) - IPsec SA Encryption Settings
AES-256 / SHA - IPsec Pre-Shard Key
vpn
RIP (Routing Information Protocol) is one of the routing protocols you need to understand if you want to pass the Cisco CCNA exam. If you have no idea how RIP works I suggest to read this lesson first where I explain how RIP works. In this lesson I'll show you how to configure RIP on a Cisco router. Moneydance 2019 3 1880 download free. This is the topology that I will use:
Above we see 3 routers called R1, R2 and R3. There are a couple of networks so we'll have something to advertise in RIP. First let's configure all the interfaces:
Before we continue RIP we'll check the routing tables:
Our routers only know 1 thing…their directly connected interfaces. Let's configure RIP and see what happens:
We use the router rip command to go to the RIP configuration. Next step is to use the network command which does two things:
Let's zoom in on R1 and R2 so I can explain this a bit more…
